Annex — - Appendix 2 Europese Overeenkomst nopens de arbeidsvoorwaarden voor de bemanningen van motorrijtuigen in het internationale vervoer over de weg (AETR)
- Appendix 2
I. APPROVAL MARK
1. The approval mark shall be made up of:
A rectangle, within which shall be placed the letter “e” followed by a distinguishing number for the country which has issued the approval in accordance with the following conventional signs:
Germany | - 1
France | - 2
Italy | - 3
Netherlands | - 4
Sweden | - 5
Belgium | - 6
Hungary | 7
Czech Republic | - 8
Spain | - 9
Serbia | 10
United Kingdom | -11
Austria | -12
Luxemburg | -13
Switzerland | 14
Norway | -16
Finland | 17
Denmark | -18
Poland | -20
Portugal | -21
Russian Federation | -22
Greece | -23
Ireland | -24
Croatia | -25
Liechtenstein | 33
Bulgaria | 34
Kazakhstan | 35
Lithuania | 36
Turkey | 37
Turkmenistan | 38
Azerbaijan | 39
The former Yugoslav Republic of Macedonia | 40
Andorra | 41
Uzbekistan | 44
Cyprus | 49
Malta | 50
Albania | 54
Armenia | 55
Montenegro | 56
San Marino | 57
Monaco | 59
Subsequent numbers shall be assigned:
(i) To countries Contracting Parties to the 1958 Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts the same numbers as assigned to those countries by that Agreement;
(ii) To countries non-Contracting Parties to the 1958 Agreement - in the chronological order in which they ratify or accede to this Agreement
and
An approval number corresponding to the number of the approval certificate drawn up for the prototype of the control device or the record sheet, placed at any point within the immediate proximity of their rectangle.
Note: In order to ensure in the future conformity between conventional signs in the 1958 Agreement and those set up in the AETR Agreement new Contracting Parties should be allocated the same number in both Agreements.
2. The approval mark shall be shown on the descriptive plaque of each set of control device and on each record sheet. It must be indelible and must always remain clearly legible.
3. The dimensions of the approval mark drawn below are expressed in millimetres, these dimensions being minima. The ratios between the dimensions must be maintained.
II. Approval certificate for products in accordance with appendix I
III. Approval certificate for products in accordance with Appendix 1B
Once the Contracting Party has effected an approval it issues the applicant with an approval certificate, drawn up in accordance with the model below. Contracting Parties use copies of this document in order to communicate to other Contracting Parties approvals granted or any withdrawals.
Approval certificate for products in accordance with appendix 1B
Name of the competent administration .........................
Communication concerning (1):
¤ Approval
¤ Withdrawal of an approval
¤ Of a control device model
¤ Of a control device component (2)
¤ Of a driver card
¤ Of a workshop card
¤ Of a company card
¤ Of an inspector’s card
Approval No. .........................
1. Manufacturing or commercial mark .........................
2. Name of model .........................
3. Name of manufacturer .........................
4. Address of manufacturer .........................
5. Submitted for approval on .........................
6. Test laboratory or laboratories .........................
7. Date and No. of reports .........................
8. Date of approval .........................
9. Date of withdrawal of approval .........................
10. Model(s) of component(s) of control device with which the component is intended to be used .........................
11. Place .........................
12. Date .........................
13. Descriptive documents annexed .........................
14. Remarks (including the affixing of seals if required) .........................
(Signature)
(1) Tick the relevant boxes
(2) Specify the component concerned in the communication” "
- Regeling
- Europese Overeenkomst nopens de arbeidsvoorwaarden voor de bemanningen van motorrijtuigen in het internationale vervoer over de weg (AETR)
- Afkortingen
- AETR
- Soort
- Verdrag
- Geldend vanaf
- 23-04-2022
- BWB-id
- BWBV0004455
- Versie
- 2022-04-23_0