A. MODEL FORM OF CERTIFICATE OF COMPLIANCE OF THE EQUIPMENT, AS PRESCRIBED IN ANNEX 1, APPENDIX 1, PARAGRAPH 3

FORM OF CERTIFICATE FOR INSULATED, REFRIGERATED, MECHANICALLY REFRIGERATED, HEATED OR MECHANICALLY REFRIGERATED AND HEATED EQUIPMENT USED FOR THE INTERNATIONAL CARRIAGE OF PERISHABLE FOODSTUFFS BY LAND

6. | | | / Is approved as: 7 | XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

6.1. | | | / With one or more thermal appliances which is (are) 1:

6.1.1 | | / Independent; 8 | MAKE, MODEL, REFRIGERANT, SERIAL NUMBER/YEAR OF MANUFACTURE (If any)

6.1.2 | | / dependent; 8 | MAKE, MODEL, REFRIGERANT, SERIAL NUMBER/YEAR OF MANUFACTURE (If any)

6.1.3 | | / Removable;

6.1.4 | | / Not removable.

7. | | | / Basis of issue of certificate:

7.1 | | | | / This certificate is issued on the basis of: 1

7.1.1 | | | / Tests of the equipment;

7.1.2 | | | | | / conformity with a reference item of equipment;

7.1.3 | | | /A periodic inspection.

7.2 | | | / Specify:

7.2.1 | | / The testing station; | | XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

7.2.2 | | | / The nature of the tests: 9 | XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX

7.2.3 | | | | / The number(s) of the report(s):

NNNNNNNN (TESTING STATION) YYYY/MM/DD and NNNNNNNN (TESTING STATION) YYYY/MM/DD

7.2.4 | | / The K coefflcient: 0,nn W/m2K | | Nominal capacity | Evap.1 | Evap.2 | Evap.3

oC | xxxx W | xxxx W | xxxx W | xxxx W

/ The effective refrigerating capacity at an outside temperature of 30 °C and an inside temperature of: 10 | oC | xxxx W | xxxx W | xxxx W | xxxx W

oC | xxxx W | xxxx W | xxxx W | xxxx W

7.2.6 | | XX air changes/hour11

7.3 | | | | Number of openings and special equipment X

7.3.1 | | / Number of doors: | X | / rear door | X | / side door(s) | X

7.3.2 | | | / Number of vents: | X

7.3.3 | | | / Hanging meat equipment; | X

7.4 | | | / Others

These footnotes shall not be printed on the certificate itself

The areas in grey shall be replaced by the translation in the language of the country issuing the ATP Certificate.

1 / Strike out what does not apply.

2 / Distinguishing sign of the country, as used in international road traffic.

3 / The number (figures, letters, etc.) indicating the authority issuing the certificate and the approval reference.

4 / Multi-temperature equipment is insulated equipment with two or more compartments for different temperatures in each compartment. For multi-temperature equipment a declaration of conformity (see 7.3.6 of annex 1, appendix 2) shall be carried in addition to the ATP certificate.

5 / The blank certificate shall be printed in the language of the issuing country and in English, French or Russian; the various items shall be numbered as in the above model.

6 / State type (wagon, lorry, trailer, semi-trailer, container, etc.); in the case of tank equipment for carriage of liquid foodstuffs, add the word “tank”.

7 / Enter here one or more of the descriptions listed in Appendix 4 of Annex 1, together with the corresponding distinguishing mark or marks.

8 / Write the make, model, refrigerant, serial number and year of manufacture of the equipment.

9 / Measurement of the overall coefficient of heat transfer, determination of the efficiency of cooling appliances, etc.

10 / Where determined in conformity with the provisions of Appendix 2, paragraph 3.2, of this Annex.

11 Where XX is the number of air changes per hour calculated by dividing the total airflow of the circulation fans by the total internal volume of the equipment. In the case of multi-compartment equipment with movable bulkheads, the total airflow of the circulation fans has to be divided by the maximum internal volume of each compartment.

12 / The effective cooling capacity of each evaporator depends on the number of evaporators fixed at the condensing unit.

13 / In case of loss, a new Certificate can be provided or, instead of it, a photocopy of the ATP Certificate bearing a special stamp with “CERTIFIED DUPLICATE” (in red ink) and the name of the certifying officer, signature, and the name of the competent authority or authorized body.

14 / Security stamp (relief, fluorescent, ultraviolet, or other safety mark that certifies the origin of the certificate).

15 / If applicable, mention the way the power for issuing ATP Certificates is delegated.

16 / Write the mark, model, serial number of the manufacturer and month and year of manufacture of the insulated body. All the serial numbers of insulated equipment (containers) having an internal volume of less than 2 m3 shall be listed. It is also acceptable to collectively list these numbers, i.e. from number … to number ….

B. CERTIFICATION PLATE OF COMPLIANCE OF THE EQUIPMENT, AS PROVIDED FOR IN ANNEX 1, APPENDIX 1, PARAGRAPH 3

1. The certification plate shall be affixed to the equipment permanently and in a clearly visible place adjacent to any other approval plate issued for official purposes. The plate, conforming to the model reproduced below, shall take the form of a rectangular, corrosion-resistant and fire-resistant plate measuring at least 160 mm by 100 mm. The following particulars shall be indicated legibly and indelibly on the plate in at least the English or French or Russian language:

a) the Latin letters “ATP” followed by the words “APPROVED FOR TRANSPORT OF PERISHABLE FOODSTUFFS”;

b) “APPROVAL NUMBER” followed by the distinguishing sign (in international road traffic) of the State in which the approval was granted and the number (figures, letters, etc.) of the approval reference;

c) “EQUIPMENT NUMBER” followed by the individual number assigned to identify the particular item of equipment (which may be the manufacturer’s number);

d) “ATP MARK” followed by the distinguishing mark prescribed in annex l, appendix 4, corresponding to the class and the category of the equipment;

e) “VALID UNTIL” followed by the date (month and year) when the approval of the unit of equipment expires. If the approval is renewed following a test or inspection, the subsequent date of expiry may be added on the same line.

2. The letters “ATP” and the letters of the distinguishing mark should be approximately 20 mm high. Other letters and figures should not be less than 5 mm high.